TungMeister

Endmill with exchangeable heads for reduced tool change time

Choose the best head-shank combination for your endmilling operation
Minimize setup time while maximizing your productivity

Applications & Features

Applications

Shoulder milling

Shoulder milling R

Face milling

Slotting

Slotting R

Side slotting

Side milling

Pocketing

Ramping

Profiling

Plunging

Hole enlarging

Holemaking

Counterboring

Hole chamfering

Chamfering

External thread milling

Internal Thread milling

Features

1. Wide range of geometries

• 45 kinds of geometries are available. The head indexing is easy and highly accurate with the precision thread.

2. Three kinds of shank material

• Users can choose the most suitable combination according to the machining parameters, length and application required.

3. No setup time

Machine downtime is decreased considerably. Simplified setup since only the head is indexed.

4. High accuracy and repeatability

Repeatability and accuracy are maintained due to full contact of both taper and face.

Heads & Grades

Inserts

Grades

AH735

Nano-multilayered coating
Priority on chipping and fracture resistance

LEARN MORE

AH715

Nano-multilayered coating
Excellent longer tool life than existing grade

LEARN MORE

GH130

High chipping and fracture resistance
Suitable for steel, stainless steel, and cast iron

LEARN MORE

GH730

Good balance between wear and chipping resistance
First choice for slotting of various materials

LEARN MORE

Tools

Shank Type

Straight neck and cylindrical shank

Straight shank and neck with coolant hole

Straight neck and weldon shank

High-rigidity shank

Straight shank and taper neck

Straight shank and taper neck with coolant hole

LEARN MORE

Practical examples

Example #1

Part:	Gear
Material:	SCM420 / 18CrMo4
Shank:	VSSD16L100S10-S (Steel, ø16 mm)
Head:	VEE160L12.0C60I04S10 (ø16 mm)
Grade:	AH715
Cutting conditions:	Vc = 100 (m/min) fz = 0.09 (mm/t) ap = 10 (mm) ae = 0.1 (mm) Coolant: Wet

Example #2

Part:	Shaft
Material:	S45C / C45
Shank:	VSSD10L075S06-S (Steel, ø10 mm)
Head:	VEH100L15.0R10I04S06 (ø10 mm)
Grade:	AH715
Cutting conditions:	Vc = 100 (m/min) fz = 0.05 (mm/t) ap = 1 (mm) ae = 6 (mm) Coolant: Wet

Example #3

Part:	Rack
Material:	SCM440 / 42CrMo4
Shank:	VSSD25L075S12-S (Steel, ø25 mm)
Head:	VEH200L30.0R05I04S12 (ø20 mm)
Grade:	AH715
Cutting conditions:	Vc = 140 (m/min) fz = 0.08 (mm/t) ap = 24 (mm) ae = 5.5 (mm) Coolant: Wet

View more reports

Standard cutting conditions

Square - Shoulder milling

VEH, VEE: 3 flutes, VED / VEE: 4 flutes, VEE-A, VEE-I, VEE-R, VED-R, VEE-C

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth: fz (mm/t)									Depth of cut ap (mm)	Width of cut ae(mm)
			Tool diameter: DC (mm)
			5	6	8	10	12	16	20	25	32
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	80 – 180	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	60 – 140	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	60 – 120	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	40 – 100	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	80 – 200	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	80 – 200	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Aluminium alloys Si < 13%	–	200 – 700	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Aluminium alloys Si ≥ 13%	–	100 – 300	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	40 – 80	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	20 – 40	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	40 – 80	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	20 – 60	0.03 – 0.07	0.03 – 0.07	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.1 – 0.18	0.6 x DC	0.25 x DC

VED / VEE: 6 flutes, VED / VEE: 8, 10 flutes, VED: 7, 9 flutes

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth: fz (mm/t)						Depth of cut ap (mm)	Width of cut ae(mm)
			Tool diameter: DC (mm)
			8	10	12	16	20	25
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	60 – 120	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.6 x DC	0.02 x DC
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	30 – 60	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.6 x DC	0.02 x DC
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	80 – 160	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.6 x DC	0.02 x DC
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	40 – 90	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	0.6 x DC	0.02 x DC

Square - Slotting

VEH, VEE: 3 flutes, VED/VEE: 4 flutes, VEE-A, VEE-I, VEE-R, VEE-C

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth: fz (mm/t)									Depth of cut ap (mm)
			Tool diameter: DC (mm)
			5	6	8	10	12	16	20	25	32
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	50 – 70	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	40 – 80	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	40 – 70	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	30 – 60	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	50 – 120	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	50 – 120	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Aluminium alloys Si < 13%	–	130 – 400	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Aluminium alloys Si ≥ 13%	–	70 – 200	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	20 – 40	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	10 – 20	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	25 – 60	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	10 – 30	0.03 – 0.04	0.03 – 0.04	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.07 – 0.1	0.07 – 0.1	0.5 x DC

Face milling

VFM

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth: fz (mm/t)				Depth of cut ap (mm)	Width of cut ae(mm)
			Tool diameter: DC (mm)
			12	16	20	25
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	80 – 180	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	60 – 140	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	60 – 120	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	40 – 100	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	80 – 200	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	80 – 200	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Aluminium alloys Si < 13%	–	200 – 700	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Aluminium alloys Si ≥ 13%	–	100 – 300	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	40 – 80	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	20 – 40	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	40 – 80	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	20 – 60	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.1 – 0.17	1	0.7 x DC

High feed milling

VFX: 2, 4, 6 flutes

ISO	Workpiece material	Hardness	Cutting speed Vc (m/min)	ø10		ø12		ø16		ø20		Width of cut ae (mm)
ISO	Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth fz (mm/t)	Depth of cut ap (mm)	Feed per tooth fz (mm/t)	Depth of cut ap (mm)	Feed per tooth fz (mm/t)	Depth of cut ap (mm)	Feed per tooth fz (mm/t)	Depth of cut ap (mm)	Width of cut ae (mm)
	Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	100 – 200	0.3 – 0.7	0.5	0.4 – 0.8	0.5	0.5 – 0.9	0.75	0.6 – 1	1	0.6 x DC
	Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	80 – 180	0.2 – 0.6	0.5	0.3 – 0.7	0.5	0.4 – 0.8	0.75	0.5 – 0.9	1	0.6 x DC
	Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	80 – 160	0.2 – 0.5	0.4	0.2 – 0.5	0.4	0.3 – 0.6	0.5	0.3 – 0.6	0.75	0.6 x DC
	Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	60 – 100	0.2 – 0.6	0.4	0.2 – 0.6	0.4	0.3 – 0.7	0.5	0.3 – 0.7	0.75	0.6 x DC
	Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	100 – 220	0.3 – 0.7	0.5	0.4 – 0.8	0.75	0.5 – 0.9	0.75	0.6 – 1	1	0.6 x DC
	Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	100 – 220	0.2 – 0.6	0.5	0.3 – 0.7	0.75	0.4 – 0.8	0.75	0.5 – 0.9	1	0.6 x DC
	Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	40 – 80	0.2 – 0.5	0.4	0.2 – 0.5	0.4	0.2 – 0.6	0.5	0.2 – 0.6	0.5	0.25 x DC
	Heat-resistant alloys Inconel 718, etc.	– 40 HRC	20 – 40	0.1 – 0.3	0.3	0.1 – 0.3	0.3	0.1 – 0.3	0.4	0.1 – 0.3	0.4	0.25 x DC
	Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	40 – 80	0.2 – 0.4	0.3	0.2 – 0.4	0.3	0.3 – 0.5	0.4	0.3 – 0.5	0.4	0.45 x DC
	Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	20 – 60	0.1 – 0.2	0.2	0.1 – 0.2	0.2	0.1 – 0.3	0.3	0.1 – 0.3	0.3	0.25 x DC

Please note that the feed per tooth should not exceed the maximum feed per tooth for each product.

Ball - Profiling for roughing

VBB-BM / BG / SG, VBD-BG, VBE-BGA

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth: fz (mm/t)								Depth of cut ap (mm)	Pick feed Pf (mm)
			Tool diameter: DC (mm)
			5	6	8	10	12	16	20	25
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	100 – 200	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.4 x DC
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	80 – 180	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.4 x DC
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	80 – 160	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.4 x DC
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	60 – 100	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.4 x DC
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	100 – 220	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.4 x DC
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	100 – 220	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.4 x DC
Aluminium alloys Si < 13%	–	200 – 700	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.4 x DC
Aluminium alloys Si ≥ 13%	–	100 – 300	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.4 x DC
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	40 – 80	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.2 x DC
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	20 – 40	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.2 x DC
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	40 – 80	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.2 x DC
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	20 – 60	0.03 – 0.07	0.03 – 0.07	0.04 – 0.08	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.08 – 0.15	0.08 – 0.15	0.3 x DC	0.2 x DC

Ball - Profiling for semi-finishing and finishing

VBB-BM / BG / SG, VBD-BG, VBE-BGA

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth: fz (mm/t)								Depth of cut ap (mm)	Pick feed Pf (mm)
			Tool diameter: DC (mm)
			5	6	8	10	12	16	20	25
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	120 – 250	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.1 x DC	0.15 x DC
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	100 – 220	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.1 x DC	0.15 x DC
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	100 – 200	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.1 x DC	0.15 x DC
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	80 – 120	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.1 x DC	0.15 x DC
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	120 – 280	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.1 x DC	0.15 x DC
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	120 – 280	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.1 x DC	0.15 x DC
Aluminium alloys Si < 13%	–	300 – 1000	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.1 x DC	0.15 x DC
Aluminium alloys Si ≥ 13%	–	150 – 400	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.1 x DC	0.15 x DC
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	50 – 100	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.08 x DC	0.1 x DC
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	30 – 50	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.08 x DC	0.1 x DC
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	50 – 100	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.08 x DC	0.1 x DC
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	30 – 80	0.04 – 0.09	0.04 – 0.09	0.06 – 0.11	0.07 – 0.12	0.08 – 0.13	0.09 – 0.16	0.1 – 0.18	0.1 – 0.18	0.08 x DC	0.1 x DC

Radius - Shoulder milling

VRB, VRC, VRD

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth: fz (mm/t)					Depth of cut ap (mm)	Width of cut ae(mm)
			Tool diameter: DC (mm)
			8	10	12	16	20
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	80 – 180	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	60 – 140	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	60 – 120	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	40 – 100	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	80 – 200	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	80 – 200	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Aluminium alloys Si < 13%	–	200 – 700	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Aluminium alloys Si ≥ 13%	–	100 – 300	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	40 – 80	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	20 – 40	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	40 – 80	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	20 – 60	0.05 – 0.09	0.07 – 0.12	0.08 – 0.13	0.09 – 0.15	0.1 – 0.17	0.6 x DC	0.25 x DC

Radius - Slotting

VRB, VRC, VRD

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth: fz (mm/t)					Depth of cut ap (mm)
			Tool diameter: DC (mm)
			8	10	12	16	20
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	50 – 70	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	40 – 80	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	40 – 70	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	30 – 60	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	50 – 120	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	50 – 120	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Aluminium alloys Si < 13%	–	130 – 400	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Aluminium alloys Si ≥ 13%	–	70 – 200	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	20 – 40	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	10 – 20	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	25 – 60	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	10 – 30	0.03 – 0.04	0.04 – 0.05	0.05 – 0.06	0.06 – 0.08	0.07 – 0.1	0.5 x DC

Barrel, Bull nose, Lens - Profiling

VBO, VBN, VBL

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth: fz (mm/t)			Cusp height (mm)
			Tool diameter: DC (mm)
			10	12	16
Low carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	100 – 200	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
High carbon steel SCM440, SCr415, etc. 42CrMo4, 15Cr3, etc.	– 300 HB	80 – 180	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	80 – 160	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	60 – 100	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Grey cast iron FC250, FC300, etc. 250, 300, etc.	150 – 250 HB	100 – 220	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Ductile cast iron FCD400, etc. 400-15S, etc.	150 – 250 HB	100 – 220	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Aluminium alloys Si < 13%	–	200 – 700	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Aluminium alloys Si ≥13%	–	100 – 300	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	40 – 80	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Heat-resistant alloys Inconel718, etc.	50 – 60 HRC	20 – 40	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Hardened steel SKD61, SKT4, etc. X40CrMoV5-1, 55NiCrMoV6, etc.	–	40 – 80	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1
Hardened steel SKD11, SKH, etc. X153CrMoV12, HS18-0-1, etc.	50 – 60 HRC	20 – 60	0.05 – 0.1	0.06 – 0.11	0.07 – 0.13	0.1

Chamfering and countersinking (Milling, Z-feed chamfering)

VCA, VCW, VCR

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth fz (mm/t)
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	60 – 100	0.03 – 0.06
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	50 – 80	0.03 – 0.06
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	40 – 70	0.03 – 0.06
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	30 – 50	0.03 – 0.06
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	80 – 120	0.03 – 0.06
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	80 – 120	0.03 – 0.06
Aluminium alloys	–	100 – 200	0.04 – 0.08
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	30 – 50	0.025 – 0.05
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	20 – 40	0.02 – 0.04
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	30 – 50	0.025 – 0.05
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	20 – 40	0.02 – 0.04

Spot drill

VCP, VDS

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed f (mm/rev)
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	60 – 100	0.06 – 0.12
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	50 – 80	0.06 – 0.12
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	40 – 70	0.06 – 0.12
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	30 – 50	0.06 – 0.12
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	80 – 120	0.06 – 0.12
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	80 – 120	0.06 – 0.12
Aluminium alloys	–	100 – 200	0.08 – 0.16
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	30 – 50	0.05 – 0.1
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	20 – 40	0.04 – 0.08
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	30 – 50	0.05 – 0.1
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	20 – 40	0.04 – 0.08

Center drill

VDP

ISO	Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed : f (mm/rev)
ISO	Workpiece material	Hardness	Cutting speed Vc (m/min)	VDP107	VDP165	VDP2	VDP3	VDP4	VDP5	VDP6
	Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	40 – 80	0.02 – 0.04	0.025 – 0.05	0.025 – 0.05	0.04 – 0.08	0.05 – 0.1	0.05 – 0.1	0.06 – 0.12
	Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	30 – 50	0.02 – 0.04	0.025 – 0.05	0.025 – 0.05	0.04 – 0.08	0.05 – 0.1	0.05 – 0.1	0.06 – 0.12
	Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	20 – 30	0.02 – 0.04	0.025 – 0.05	0.025 – 0.05	0.04 – 0.08	0.05 – 0.1	0.05 – 0.1	0.06 – 0.12
	Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	15 – 25	0.015 – 0.03	0.02 – 0.04	0.02 – 0.04	0.04 – 0.08	0.05 – 0.1	0.05 – 0.1	0.06 – 0.12
	Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	60 – 100	0.02 – 0.04	0.025 – 0.05	0.025 – 0.05	0.05 -0.09	0.07 – 0.012	0.07 – 0.12	0.12 – 0.18
	Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	60 – 100	0.02 – 0.04	0.025 – 0.05	0.025 – 0.05	0.04 – 0.08	0.05 – 0.1	0.05 – 0.1	0.1 – 0.15
	Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	15 – 25	0.01 – 0.02	0.01 – 0.02	0.015 – 0.03	0.04 – 0.07	0.04 – 0.07	0.04 – 0.07	0.04 – 0.07
	Heat-resistant alloys Inconel 718, etc.	– 40 HRC	10 – 20	0.01 – 0.02	0.01 – 0.02	0.015 – 0.03	0.03 – 0.06	0.03 – 0.06	0.03 – 0.06	0.03 – 0.06
	Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	15 – 25	–	–	–	0.04 – 0.07	0.04 – 0.07	0.04 – 0.07	0.04 – 0.07
	Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	10 – 20	–	–	–	0.03 – 0.06	0.03 – 0.06	0.03 – 0.06	0.03 – 0.06

—0.03 – 0.060.03 – 0.060.03 – 0.060.03 – 0.06

Counterboring

VGC

Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth fz (mm/t)
Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	40 – 80	0.04 – 0.08
Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	30 – 50	0.04 – 0.08
Prehardened steel PX5, NAK80, etc.	30 – 40 HRC	20 – 30	0.04 – 0.08
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	15 – 25	0.04 – 0.08
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	60 – 100	0.05 – 0.09
Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	60 – 100	0.04 – 0.08
Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	15 – 25	0.04 – 0.07
Heat-resistant alloys Inconel 718, etc.	– 40 HRC	10 – 20	0.03 – 0.06
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc.	40 – 50 HRC	15 – 25	0.04 – 0.07
Hardened steel SKD11, SKH51, etc. HS6-5-2, etc.	50 – 60 HRC	10 – 20	0.03 – 0.06

When drilling, pecking operation should be applied with the depth of 0.3 – 0.5 mm per step.
Apply the same cutting conditions as the VEE type head when conducting shoulder milling or slotting operations.

Slotting

ISO	Workpiece material	Hardness	VST		VTB
ISO	Workpiece material	Hardness	Cutting speed Vc (m/min)	Feed per tooth fz (mm/t)	Cutting speed Vc (m/min)	Feed per tooth fz (mm/t)
	Carbon steel S45C, S55C, etc. C45, C55, etc.	– 300 HB	80 – 180	0.05 – 0.15	80 – 180	0.08 – 0.18
	Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc.	– 300 HB	60 – 120	0.04 – 0.12	60 – 120	0.05 – 0.15
	Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc.	– 200 HB	50 – 120	0.04 – 0.12	50 – 120	0.05 – 0.15
	Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc.	150 – 250 HB	100 – 200	0.05 – 0.15	100 – 200	0.08 – 0.18
	Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc.	150 – 250 HB	100 – 200	0.04 – 0.12	100 – 200	0.05 – 0.15
	Aluminium alloys Si < 13%	–	200 – 600	0.05 – 0.15	200 – 600	0.08 – 0.18
	Aluminium alloys Si ≥ 13%	–	100 – 300	0.03 – 0.13	100 – 300	0.05 – 0.15
	Titanium alloys Ti-6Al-4V, etc.	– 40 HRC	40 – 60	0.04 – 0.12	40 – 60	0.05 – 0.15
	Heat-resistant alloys Inconel 718, etc.	– 40 HRC	15 – 35	0.02 – 0.1	15 – 35	0.02 – 0.1

Indexable modular head

HPAV06-S

Workpiece materials		Hardness	Priority	Grades	Cutting speed Vc (m/min)	Feed per tooth fz (mm/t)
Low carbon steel S15C / C15E4, SS400 / E275A, etc.		– 200 HB	First choice	AH3225	230 – 430	0.07 – 0.12
Carbon steel and alloy steel S55C / C55, SCM440 / 42CrMo4, etc.		– 300 HB	First choice	AH3225	150 – 350	0.07 – 0.12
Prehardend steel NAK80, PX5, etc.		30 – 40 HRC	First choice	AH3225	100 – 230	0.07 – 0.12
Stainless steel SUS304 / X5CrNi18-9, SUS316 / X5CrNiMo17-12-3, etc.		–	First choice	AH3135	150 – 220	0.06 – 0.1
Grey cast iron FC250 / 250, FC300 / 300, etc.		150 – 250 HB	First choice	AH120	200 – 330	0.07 – 0.12
Ductile cast iron FCD400, FCD600 / 600-3, etc.		150 – 250 HB	First choice	AH120	150 – 240	0.07 – 0.12
Aluminium alloys Si < 13%		–	First choice	KS05F	650 – 1000	0.07 – 0.12
Aluminium alloys Si ≥ 13%		–	First choice	KS05F	100 – 230	0.04 – 0.12
Titanium alloys Ti-6AI-4V, etc.		– 40 HRC	First choice	AH130	40 – 90	0.04 – 0.1
Superalloys Inconel718, etc.		– 40 HRC	First choice	AH130	45 – 65	0.04 – 0.09
Hardened steel	SKD61 / X40CrMoV5-1, etc.	40 – 50 HRC	First choice	AH120	45 – 70	0.04 – 0.08
Hardened steel	SKD11 / X153CrMoV12, etc.	50 – 60 HRC	First choice	AH120	40 – 65	0.04 – 0.06

Threading

VMT, VTR

Material		Condition	Tensile strength [N/mm²]	Hardness	Cutting speed (m/min)	Tool dia. (mm)
					Cutting speed (m/min)	Feed (mm/t)
					AH725	ø10	ø12	ø15.4, ø15.7, ø16	ø21.7
Non-alloy steel and cast steel, free cutting steel	< 0.25 %C	Annealed	420	125 HB	100 – 250	0.08	0.09	0.12	0.15
	≥ 0.25 %C	Annealed	650	190 HB	80 – 210	0.08	0.09	0.12	0.15
	< 0.55 %C	Quenched and tempered	850	250 HB	65 – 170
	≥ 0.55 %C	Annealed	750	220 HB	110 – 180	0.07	0.08	0.1	0.12
		Quenched and tempered	1000	300 HB	95 – 160	0.07	0.08	0.1	0.12
Low alloy steel and cast steel (less than 5% of alloying elements)		Annealed	600	200 HB	90 – 160	0.05	0.05	0.07	0.08
		Quenched and tempered	930	275 HB	65 – 200	0.05	0.05	0.07	0.08
			1000	300 HB	70 – 210	0.05	0.05	0.07	0.08
			1200	350 HB	95 – 160	0.05	0.05	0.07	0.08
High alloyed steel, cast steel, and tool steel		Annealed	680	200 HB	130 – 170	0.05	0.05	0.07	0.08
High alloyed steel, cast steel, and tool steel		Quenched and tempered	1100	325 HB	75 – 100	0.05	0.05	0.07	0.08
Stainless steel and cast steel		Ferritic/martensitic	680	200 HB	110 – 170	0.05	0.05	0.07	0.08
Stainless steel and cast steel		Martensitic	820	240 HB	70 – 155	0.05	0.05	0.07	0.08
Stainless steel		Annealed	600	180 HB	85 – 100	0.05	0.05	0.07	0.08
Cast iron nodular (GGG)		Ferritic/martensitic		180 HB	120 – 160	0.08	0.09	0.12	0.15
Cast iron nodular (GGG)		Pearlitic		260 HB	75 – 160	0.08	0.09	0.12	0.15
Grey cast iron (GG)		Ferritic		160 HB	70 – 150	0.08	0.09	0.12	0.15
Grey cast iron (GG)		Pearlitic		250 HB	110 – 140	0.08	0.09	0.12	0.15
Malleable cast iron		Ferritic		130 HB	120 – 160	0.08	0.09	0.12	0.15
Malleable cast iron		Pearlitic		230 HB	110 – 140	0.08	0.09	0.21	0.15
Aluminium-wrought alloy		Not cureable		60 HB	160 – 300	0.08	0.09	0.12	0.15
Aluminium-wrought alloy		Cured		100 HB
Aluminium-cast, alloyed	≤12% Si	Not cureable		75 HB	150 – 350	0.08	0.09	0.12	0.15
		Cured		90 HB
	>12% Si	High temperature		130 HB	100 – 250	0.05	0.05	0.07	0.08
Copper alloys	>1% Pb	Free cutting		110 HB
		Brass		90 HB
		Electrolitic copper		100 HB
Non-metallic		Duroplastics, fiber plastics			100 – 400	0.11	0.12	0.15	0.18
Non-metallic		Hard rubber
High temp. alloys	Fe based	Annealed		200 HB
	Fe based	Cured		280 HB
	Ni or Co based	Annealed		250 HB	20 – 80	0.03	0.03	0.04	0.04
		Cured		350 HB
		Cast		320 HB
Titanium Ti alloys			RM 400
Titanium Ti alloys		Alpha+beta alloys cured	RM 1050		20 – 80	0.03	0.03	0.04	0.04
Hardened steel		Hardened		55 HRC	55 – 65
Hardened steel		Hardened		60 HRC	45 – 55
Chilled cast iron		Cast		400 HB	90 – 105
Cast iron		Hardened		55 HRC	55 – 65

For more information about this product, visit our online e-catalog or download the product report:

e-Catalog

Metric | Imperial

PDF

Metric

Main product report_No. 381-G

Imperial

No. 381-US
- No. 381S5-US(GH730 grade and chamfering and Expansion rough shoulder milling head lines)

BACK

Szukaj

Search for:

Powiązane wiadomości

03 lut 2025

Sklep on-line

Sklep on-line
Znajdź i zamów narzędzia online

więcej...

e-Katalog

Katalog elektroniczny
Ściągnij rysunki CAD i modele 3D

więcej...

Aplikacje i przydatne narzędzia

Tungaloy APP
TUNG NaviNawigator do wyboru odpowiedniego narzędzia TUNGALOY
Kalkulator parametrów
Kalkulator do obliczania parametrów skrawania
Przewodnik doboru płytek do toczenia
Przewodnik doboru łamaczy i gatunków do płytek tokarskich
MatrixSystem zarządzania narzędziami

Najczęściej zadawane pytania KONTAKT

TungMeister

Endmill with exchangeable heads for reduced tool change time

Applications & Features

Applications

Features

1. Wide range of geometries

2. Three kinds of shank material

3. No setup time

4. High accuracy and repeatability

Heads & Grades

Inserts

Square heads

Face milling heads

High feed milling heads

Ball heads

Radius heads

Barrel heads

Chamfering,Spot drill heads

Chamfering heads

Center hole heads

Counterboring heads

Slotting heads

Threading heads

Grades

AH735

AH715

GH130

GH730

Tools

Shank Type

Straight neck and cylindrical shank

Straight shank and neck with coolant hole

Straight neck and weldon shank

High-rigidity shank

Straight shank and taper neck

Straight shank and taper neck with coolant hole

Practical examples

Example #1

Example #2

Example #3

Standard cutting conditions

Square - Shoulder milling

Square - Slotting

Face milling

High feed milling

Ball - Profiling for roughing

Ball - Profiling for semi-finishing and finishing

Radius - Shoulder milling

Radius - Slotting

Barrel, Bull nose, Lens - Profiling

Chamfering and countersinking (Milling, Z-feed chamfering)

Spot drill

Center drill

Counterboring

Slotting

Indexable modular head

Threading

e-Catalog

PDF

Metric

Imperial

Szukaj

Powiązane wiadomości

High-efficiency head exchangeable end mill series TungMeister significantly expanded with the latest grade AH715

Tungaloy rozszerza gatunek AH715 o głowice fazujące serii TungMeister

System frezów TungMeister uzupełniono o wymienne głowiczki w rozmiarach calowych

Sklep on-line

więcej...

e-Katalog

więcej...

Aplikacje i przydatne narzędzia

SNS – Global

SNS – Tungaloy Polska Sp. z o.o.