Endmill with exchangeable heads for reduced tool change time
Choose the best head-shank combination for your endmilling operation
Minimize setup time while maximizing your productivity
การใช้งาน & คุณสมบัติ
การใช้งาน
คุณสมบัติ
1. Wide range of geometries
• 45 kinds of geometries are available. The head indexing is easy and highly accurate with the precision thread.
2. Three kinds of shank material
• Users can choose the most suitable combination according to the machining parameters, length and application required.
3. No setup time
Machine downtime is decreased considerably. Simplified setup since only the head is indexed.
4. High accuracy and repeatability
Repeatability and accuracy are maintained due to full contact of both taper and face.
เม็ดมีด & เกรด
เม็ดมีด
Square heads
Face milling heads
High feed milling heads
Chamfering,Spot drill heads
Chamfering heads
Center hole heads
Counterboring heads
Slotting heads
Threading heads
เกรด
AH735
- Nano-multilayered coating
- Priority on chipping and fracture resistance
AH715
- Nano-multilayered coating
- Excellent longer tool life than existing grade
GH130
- High chipping and fracture resistance
- Suitable for steel, stainless steel, and cast iron
GH730
- Good balance between wear and chipping resistance
- First choice for slotting of various materials
Tools
Shank Type
Straight neck and cylindrical shank
Straight shank and neck with coolant hole
Straight neck and weldon shank
High-rigidity shank
Straight shank and taper neck
Straight shank and taper neck with coolant hole
ตัวอย่างการใช้งาน
ตัวอย่างที่ #1
| ชิ้นงาน: | Gear |
| วัสดุ: | SCM420 / 18CrMo4 |
| ด้าม: | VSSD16L100S10-S (Steel, ø16 mm) |
| หัวกัด: | VEE160L12.0C60I04S10 (ø16 mm) |
| เกรด: | AH715 |
| เงื่อนไขการตัดเฉือน: | Vc = 100 (m/min) fz = 0.09 (mm/t) ap = 10 (mm) ae = 0.1 (mm) Coolant: Wet |
ตัวอย่างที่ #2
| ชิ้นงาน: | Shaft |
| วัสดุ: | S45C / C45 |
| ด้าม: | VSSD10L075S06-S (Steel, ø10 mm) |
| หัวกัด: | VEH100L15.0R10I04S06 (ø10 mm) |
| เกรด: | AH715 |
| เงื่อนไขการตัดเฉือน: | Vc = 100 (m/min) fz = 0.05 (mm/t) ap = 1 (mm) ae = 6 (mm) Coolant: Wet |
ตัวอย่างที่ #3
| ชิ้นงาน: | Rack |
| วัสดุ: | SCM440 / 42CrMo4 |
| ด้าม: | VSSD25L075S12-S (Steel, ø25 mm) |
| หัวกัด: | VEH200L30.0R05I04S12 (ø20 mm) |
| เกรด: | AH715 |
| เงื่อนไขการตัดเฉือน: | Vc = 140 (m/min) fz = 0.08 (mm/t) ap = 24 (mm) ae = 5.5 (mm) Coolant: Wet |
เงื่อนไขการตัดเฉือนมาตรฐาน
Square - Shoulder milling
VEH, VEE: 3 flutes, VED / VEE: 4 flutes, VEE-A, VEE-I, VEE-R, VED-R, VEE-C
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) | อัตราป้อนต่อฟัน: fz (มม./ฟัน) | ระยะกินลึก ap (มม.) |
Width of cut ae(มม.) |
||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Tool diameter: DC (มม.) | ||||||||||||||
| 5 | 6 | 8 | 10 | 12 | 16 | 20 | 25 | 32 | ||||||
 |
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 80 – 180 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 60 – 140 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 60 – 120 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC | |
 |
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 40 – 100 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC |
 |
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 80 – 200 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 80 – 200 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC | |
 |
Aluminium alloys Si < 13% |
– | 200 – 700 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC |
| Aluminium alloys Si ≥ 13% |
– | 100 – 300 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC | |
 |
Titanium alloys Ti-6Al-4V, etc. |
– | 40 – 80 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC |
| Heat-resistant alloys Inconel 718, etc. |
– | 20 – 40 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC | |
 |
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 40 – 80 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 20 – 60 | 0.03 – 0.07 | 0.03 – 0.07 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.1 – 0.18 | 0.6 x DC | 0.25 x DC | |
VED / VEE: 6 flutes, VED / VEE: 8, 10 flutes, VED: 7, 9 flutes
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) |
อัตราป้อนต่อฟัน: fz (มม./ฟัน) | ระยะกินลึก ap (มม.) |
Width of cut ae(มม.) |
|||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Tool diameter: DC (ม.) | |||||||||||
| 8 | 10 | 12 | 16 | 20 | 25 | ||||||
|
Titanium alloys Ti-6Al-4V, etc. |
– | 60 – 120 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.6 x DC | 0.02 x DC |
| Heat-resistant alloys Inconel 718, etc. |
– | 30 – 60 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.6 x DC | 0.02 x DC | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 80 – 160 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.6 x DC | 0.02 x DC |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 40 – 90 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 0.6 x DC | 0.02 x DC | |
Square - Slotting
VEH, VEE: 3 flutes, VED/VEE: 4 flutes, VEE-A, VEE-I, VEE-R, VEE-C
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) | อัตราป้อนต่อฟัน: fz (มม./ฟัน) | ระยะกินลึก ap (มม.) | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Tool diameter: DC (มม.) | |||||||||||||
| 5 | 6 | 8 | 10 | 12 | 16 | 20 | 25 | 32 | |||||
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 50 – 70 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 40 – 80 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 40 – 70 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 30 – 60 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 50 – 120 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 50 – 120 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC | |
|
Aluminium alloys Si < 13% |
– | 130 – 400 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC |
| Aluminium alloys Si ≥ 13% |
– | 70 – 200 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 20 – 40 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC |
| Heat-resistant alloys Inconel 718, etc. |
– | 10 – 20 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 25 – 60 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 10 – 30 | 0.03 – 0.04 | 0.03 – 0.04 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.07 – 0.1 | 0.07 – 0.1 | 0.5 x DC | |
Face milling
VFM
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) | อัตราป้อนต่อฟัน: fz (มม./ฟัน) | ระยะกินลึก ap (มม.) | Width of cut ae (มม.) | |||
|---|---|---|---|---|---|---|---|---|---|
| Tool diameter: DC (มม.) | |||||||||
| 12 | 16 | 20 | 25 | ||||||
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 80 – 180 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 60 – 140 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 60 – 120 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 40 – 100 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 80 – 200 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 80 – 200 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC | |
|
Aluminium alloys Si < 13% |
– | 200 – 700 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC |
| Aluminium alloys Si ≥ 13% |
– | 100 – 300 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 40 – 80 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC |
| Heat-resistant alloys Inconel 718, etc. |
– | 20 – 40 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 40 – 80 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 20 – 60 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.1 – 0.17 | 1 | 0.7 x DC | |
High feed milling
VFX: 2, 4, 6 flutes
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) | ø10 | ø12 | ø16 | ø20 | Width of cut ae (มม.) |
||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| อัตราป้อนต่อฟัน fz (มม./t) |
ระยะกินลึก ap (มม.) |
อัตราป้อนต่อฟัน fz (มม./ฟัน) |
ระยะกินลึก ap (มม.) |
อัตราป้อนต่อฟัน fz (มม./ฟัน) |
ระยะกินลึก ap (มม.) |
อัตราป้อนต่อฟัน fz (มม./ฟัน) |
ระยะกินลึก ap (มม.) |
|||||
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 100 – 200 | 0.3 – 0.7 | 0.5 | 0.4 – 0.8 | 0.5 | 0.5 – 0.9 | 0.75 | 0.6 – 1 | 1 | 0.6 x DC |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 80 – 180 | 0.2 – 0.6 | 0.5 | 0.3 – 0.7 | 0.5 | 0.4 – 0.8 | 0.75 | 0.5 – 0.9 | 1 | 0.6 x DC | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 80 – 160 | 0.2 – 0.5 | 0.4 | 0.2 – 0.5 | 0.4 | 0.3 – 0.6 | 0.5 | 0.3 – 0.6 | 0.75 | 0.6 x DC | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 60 – 100 | 0.2 – 0.6 | 0.4 | 0.2 – 0.6 | 0.4 | 0.3 – 0.7 | 0.5 | 0.3 – 0.7 | 0.75 | 0.6 x DC |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 100 – 220 | 0.3 – 0.7 | 0.5 | 0.4 – 0.8 | 0.75 | 0.5 – 0.9 | 0.75 | 0.6 – 1 | 1 | 0.6 x DC |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 100 – 220 | 0.2 – 0.6 | 0.5 | 0.3 – 0.7 | 0.75 | 0.4 – 0.8 | 0.75 | 0.5 – 0.9 | 1 | 0.6 x DC | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 40 – 80 | 0.2 – 0.5 | 0.4 | 0.2 – 0.5 | 0.4 | 0.2 – 0.6 | 0.5 | 0.2 – 0.6 | 0.5 | 0.25 x DC |
| Heat-resistant alloys Inconel 718, etc. |
– | 20 – 40 | 0.1 – 0.3 | 0.3 | 0.1 – 0.3 | 0.3 | 0.1 – 0.3 | 0.4 | 0.1 – 0.3 | 0.4 | 0.25 x DC | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 40 – 80 | 0.2 – 0.4 | 0.3 | 0.2 – 0.4 | 0.3 | 0.3 – 0.5 | 0.4 | 0.3 – 0.5 | 0.4 | 0.45 x DC |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 20 – 60 | 0.1 – 0.2 | 0.2 | 0.1 – 0.2 | 0.2 | 0.1 – 0.3 | 0.3 | 0.1 – 0.3 | 0.3 | 0.25 x DC | |
Please note that the feed per tooth should not exceed the maximum feed per tooth for each product.
Ball - Profiling for roughing
VBB-BM / BG / SG, VBD-BG, VBE-BGA
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) | อัตราป้อนต่อฟัน: fz (มม./ฟัน) | ระยะกินลึก ap (มม.) | Pick feed Pf (มม.) |
|||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Tool diameter: DC (มม.) | |||||||||||||
| 5 | 6 | 8 | 10 | 12 | 16 | 20 | 25 | ||||||
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 100 – 200 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.4 x DC |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 80 – 180 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.4 x DC | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 80 – 160 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.4 x DC | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 60 – 100 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.4 x DC |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 100 – 220 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.4 x DC |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 100 – 220 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.4 x DC | |
|
Aluminium alloys Si < 13% |
– | 200 – 700 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.4 x DC |
| Aluminium alloys Si ≥ 13% |
– | 100 – 300 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.4 x DC | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 40 – 80 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.2 x DC |
| Heat-resistant alloys Inconel 718, etc. |
– | 20 – 40 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.2 x DC | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 40 – 80 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.2 x DC |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 20 – 60 | 0.03 – 0.07 | 0.03 – 0.07 | 0.04 – 0.08 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.08 – 0.15 | 0.08 – 0.15 | 0.3 x DC | 0.2 x DC | |
Ball - Profiling for semi-finishing and finishing
VBB-BM / BG / SG, VBD-BG, VBE-BGA
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) |
อัตราป้อนต่อฟัน: fz (มม./ฟัน) | ระยะกินลึก ap (มม.) |
Pick feed Pf (มม.) |
|||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Tool diameter: DC (มม.) | |||||||||||||
| 5 | 6 | 8 | 10 | 12 | 16 | 20 | 25 | ||||||
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 120 – 250 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.1 x DC | 0.15 x DC |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 100 – 220 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.1 x DC | 0.15 x DC | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 100 – 200 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.1 x DC | 0.15 x DC | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 80 – 120 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.1 x DC | 0.15 x DC |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 120 – 280 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.1 x DC | 0.15 x DC |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 120 – 280 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.1 x DC | 0.15 x DC | |
|
Aluminium alloys Si < 13% |
– | 300 – 1000 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.1 x DC | 0.15 x DC |
| Aluminium alloys Si ≥ 13% |
– | 150 – 400 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.1 x DC | 0.15 x DC | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 50 – 100 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.08 x DC | 0.1 x DC |
| Heat-resistant alloys Inconel 718, etc. |
– | 30 – 50 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.08 x DC | 0.1 x DC | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 50 – 100 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.08 x DC | 0.1 x DC |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 30 – 80 | 0.04 – 0.09 | 0.04 – 0.09 | 0.06 – 0.11 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.16 | 0.1 – 0.18 | 0.1 – 0.18 | 0.08 x DC | 0.1 x DC | |
Radius - Shoulder milling
VRB, VRC, VRD
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) | อัตราป้อนต่อฟัน: fz (มม./ฟัน) | ระยะกินลึก ap (มม.) |
Width of cut ae (มม.) |
||||
|---|---|---|---|---|---|---|---|---|---|---|
| Tool diameter: DC (มม.) | ||||||||||
| 8 | 10 | 12 | 16 | 20 | ||||||
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 80 – 180 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 60 – 140 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 60 – 120 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 40 – 100 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 80 – 200 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 80 – 200 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC | |
|
Aluminium alloys Si < 13% |
– | 200 – 700 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC |
| Aluminium alloys Si ≥ 13% |
– | 100 – 300 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 40 – 80 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC |
| Heat-resistant alloys Inconel 718, etc. |
– | 20 – 40 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 40 – 80 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 20 – 60 | 0.05 – 0.09 | 0.07 – 0.12 | 0.08 – 0.13 | 0.09 – 0.15 | 0.1 – 0.17 | 0.6 x DC | 0.25 x DC | |
Radius - Slotting
VRB, VRC, VRD
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) | อัตราป้อนต่อฟัน: fz (มม./ฟัน) | ระยะกินลึก ap (มม.) |
||||
|---|---|---|---|---|---|---|---|---|---|
| Tool diameter: DC (มม.) | |||||||||
| 8 | 10 | 12 | 16 | 20 | |||||
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 50 – 70 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 40 – 80 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 40 – 70 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 30 – 60 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 50 – 120 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 50 – 120 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC | |
|
Aluminium alloys Si < 13% |
– | 130 – 400 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC |
| Aluminium alloys Si ≥ 13% |
– | 70 – 200 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 20 – 40 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC |
| Heat-resistant alloys Inconel 718, etc. |
– | 10 – 20 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 25 – 60 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 10 – 30 | 0.03 – 0.04 | 0.04 – 0.05 | 0.05 – 0.06 | 0.06 – 0.08 | 0.07 – 0.1 | 0.5 x DC | |
Barrel, Bull nose, Lens - Profiling
VBO, VBN, VBL
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) | อัตราป้อนต่อฟัน: fz (มม./ฟัน) | Cusp height (มม.) | ||
|---|---|---|---|---|---|---|---|
| Tool diameter: DC (มม.) | |||||||
| 10 | 12 | 16 | |||||
|
Low carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 100 – 200 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 |
| High carbon steel SCM440, SCr415, etc. 42CrMo4, 15Cr3, etc. |
– 300 HB | 80 – 180 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 80 – 160 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 60 – 100 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc. |
150 – 250 HB | 100 – 220 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 |
| Ductile cast iron FCD400, etc. 400-15S, etc. |
150 – 250 HB | 100 – 220 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 | |
|
Aluminium alloys Si < 13% |
– | 200 – 700 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 |
| Aluminium alloys Si ≥13% |
– | 100 – 300 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 40 – 80 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 |
| Heat-resistant alloys Inconel718, etc. |
50 – 60 HRC | 20 – 40 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 | |
|
Hardened steel SKD61, SKT4, etc. X40CrMoV5-1, 55NiCrMoV6, etc. |
– | 40 – 80 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 |
| Hardened steel SKD11, SKH, etc. X153CrMoV12, HS18-0-1, etc. |
50 – 60 HRC | 20 – 60 | 0.05 – 0.1 | 0.06 – 0.11 | 0.07 – 0.13 | 0.1 | |
Chamfering and countersinking (Milling, Z-feed chamfering)
VCA, VCW, VCR
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) |
อัตราป้อนต่อฟัน fz (มม./ฟัน) |
|---|---|---|---|---|
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 60 – 100 | 0.03 – 0.06 |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 50 – 80 | 0.03 – 0.06 | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 40 – 70 | 0.03 – 0.06 | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 30 – 50 | 0.03 – 0.06 |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 80 – 120 | 0.03 – 0.06 |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 80 – 120 | 0.03 – 0.06 | |
|
Aluminium alloys | – | 100 – 200 | 0.04 – 0.08 |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 30 – 50 | 0.025 – 0.05 |
| Heat-resistant alloys Inconel 718, etc. |
– | 20 – 40 | 0.02 – 0.04 | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 30 – 50 | 0.025 – 0.05 |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 20 – 40 | 0.02 – 0.04 |
Spot drill
VCP, VDS
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) |
อัตราป้อน f (มม./รอบ) |
|---|---|---|---|---|
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 60 – 100 | 0.06 – 0.12 |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 50 – 80 | 0.06 – 0.12 | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 40 – 70 | 0.06 – 0.12 | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 30 – 50 | 0.06 – 0.12 |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 80 – 120 | 0.06 – 0.12 |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 80 – 120 | 0.06 – 0.12 | |
|
Aluminium alloys | – | 100 – 200 | 0.08 – 0.16 |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 30 – 50 | 0.05 – 0.1 |
| Heat-resistant alloys Inconel 718, etc. |
– | 20 – 40 | 0.04 – 0.08 | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 30 – 50 | 0.05 – 0.1 |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 20 – 40 | 0.04 – 0.08 |
Center drill
VDP
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) | อัตราป้อน: f (มม./รอบ) | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| VDP107 | VDP165 | VDP2 | VDP3 | VDP4 | VDP5 | VDP6 | ||||
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 40 – 80 | 0.02 – 0.04 | 0.025 – 0.05 | 0.025 – 0.05 | 0.04 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.06 – 0.12 |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 30 – 50 | 0.02 – 0.04 | 0.025 – 0.05 | 0.025 – 0.05 | 0.04 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.06 – 0.12 | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 20 – 30 | 0.02 – 0.04 | 0.025 – 0.05 | 0.025 – 0.05 | 0.04 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.06 – 0.12 | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 15 – 25 | 0.015 – 0.03 | 0.02 – 0.04 | 0.02 – 0.04 | 0.04 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.06 – 0.12 |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 60 – 100 | 0.02 – 0.04 | 0.025 – 0.05 | 0.025 – 0.05 | 0.05 -0.09 | 0.07 – 0.012 | 0.07 – 0.12 | 0.12 – 0.18 |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 60 – 100 | 0.02 – 0.04 | 0.025 – 0.05 | 0.025 – 0.05 | 0.04 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.1 – 0.15 | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 15 – 25 | 0.01 – 0.02 | 0.01 – 0.02 | 0.015 – 0.03 | 0.04 – 0.07 | 0.04 – 0.07 | 0.04 – 0.07 | 0.04 – 0.07 |
| Heat-resistant alloys Inconel 718, etc. |
– | 10 – 20 | 0.01 – 0.02 | 0.01 – 0.02 | 0.015 – 0.03 | 0.03 – 0.06 | 0.03 – 0.06 | 0.03 – 0.06 | 0.03 – 0.06 | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 15 – 25 | – | – | – | 0.04 – 0.07 | 0.04 – 0.07 | 0.04 – 0.07 | 0.04 – 0.07 |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 10 – 20 | – | – | – | 0.03 – 0.06 | 0.03 – 0.06 | 0.03 – 0.06 | 0.03 – 0.06 | |
—0.03 – 0.060.03 – 0.060.03 – 0.060.03 – 0.06
Counterboring
VGC
| ISO | วัสดุชิ้นงาน | ค่าความหนา | ความเร็วตัด Vc (ม./นาที) |
อัตราป้อนต่อฟัน fz (มม./ฟัน) |
|---|---|---|---|---|
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 40 – 80 | 0.04 – 0.08 |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 30 – 50 | 0.04 – 0.08 | |
| Prehardened steel PX5, NAK80, etc. |
30 – 40 HRC | 20 – 30 | 0.04 – 0.08 | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 15 – 25 | 0.04 – 0.08 |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 60 – 100 | 0.05 – 0.09 |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 60 – 100 | 0.04 – 0.08 | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 15 – 25 | 0.04 – 0.07 |
| Heat-resistant alloys Inconel 718, etc. |
– | 10 – 20 | 0.03 – 0.06 | |
|
Hardened steel SKD6, SKT4, etc. 55NiCrMoV7, etc. |
40 – 50 HRC | 15 – 25 | 0.04 – 0.07 |
| Hardened steel SKD11, SKH51, etc. HS6-5-2, etc. |
50 – 60 HRC | 10 – 20 | 0.03 – 0.06 |
When drilling, pecking operation should be applied with the depth of 0.3 – 0.5 mm per step.
Apply the same cutting conditions as the VEE type head when conducting shoulder milling or slotting operations.
Slotting
| ISO | วัสดุชิ้นงาน | ค่าความหนา | VST | VTB | ||
|---|---|---|---|---|---|---|
| ความเร็วตัด Vc (ม./นาที) |
อัตราป้อนต่อฟัน fz (มม./ฟัน) |
ความเร็วตัด Vc (ม./นาที) |
อัตราป้อนต่อฟัน fz (มม./ฟัน) |
|||
|
Carbon steel S45C, S55C, etc. C45, C55, etc. |
– 300 HB | 80 – 180 | 0.05 – 0.15 | 80 – 180 | 0.08 – 0.18 |
| Alloy steel SCM440, SCr420, etc. 42CrMo4, 20Cr4, etc. |
– 300 HB | 60 – 120 | 0.04 – 0.12 | 60 – 120 | 0.05 – 0.15 | |
|
Stainless steel SUS304, SUS316, etc. X5CrNi18-9, X5CrNiMo17-12-2, etc. |
– 200 HB | 50 – 120 | 0.04 – 0.12 | 50 – 120 | 0.05 – 0.15 |
|
Grey cast iron FC250, FC300, etc. 250, 300, etc., GG250, GG300, etc. |
150 – 250 HB | 100 – 200 | 0.05 – 0.15 | 100 – 200 | 0.08 – 0.18 |
| Ductile cast iron FCD450, etc. 450-10S, etc., GGG450, etc. |
150 – 250 HB | 100 – 200 | 0.04 – 0.12 | 100 – 200 | 0.05 – 0.15 | |
|
Aluminium alloys Si < 13% |
– | 200 – 600 | 0.05 – 0.15 | 200 – 600 | 0.08 – 0.18 |
| Aluminium alloys Si ≥ 13% |
– | 100 – 300 | 0.03 – 0.13 | 100 – 300 | 0.05 – 0.15 | |
|
Titanium alloys Ti-6Al-4V, etc. |
– | 40 – 60 | 0.04 – 0.12 | 40 – 60 | 0.05 – 0.15 |
| Heat-resistant alloys Inconel 718, etc. |
– | 15 – 35 | 0.02 – 0.1 | 15 – 35 | 0.02 – 0.1 | |
Indexable modular head
HPAV06-S
| ISO | วัสดุชิ้นงาน | ค่าความหนา | คุณสมบัติ | เกรด | ความเร็วตัด Vc (ม./นาที) | อัตราป้อนต่อฟัน fz (มม./ฟัน) |
|
|---|---|---|---|---|---|---|---|
|
Low carbon steel S15C / C15E4, SS400 / E275A, etc. |
– 200 HB | First choice | AH3225 | 230 – 430 | 0.07 – 0.12 | |
| Carbon steel and alloy steel S55C / C55, SCM440 / 42CrMo4, etc. |
– 300 HB | First choice | AH3225 | 150 – 350 | 0.07 – 0.12 | ||
| Prehardend steel NAK80, PX5, etc. |
30 – 40 HRC | First choice | AH3225 | 100 – 230 | 0.07 – 0.12 | ||
|
Stainless steel SUS304 / X5CrNi18-9, SUS316 / X5CrNiMo17-12-3, etc. |
– | First choice | AH3135 | 150 – 220 | 0.06 – 0.1 | |
|
Grey cast iron FC250 / 250, FC300 / 300, etc. |
150 – 250 HB | First choice | AH120 | 200 – 330 | 0.07 – 0.12 | |
| Ductile cast iron FCD400, FCD600 / 600-3, etc. |
150 – 250 HB | First choice | AH120 | 150 – 240 | 0.07 – 0.12 | ||
|
Aluminium alloys Si < 13% |
– | First choice | KS05F | 650 – 1000 | 0.07 – 0.12 | |
| Aluminium alloys Si ≥ 13% |
– | First choice | KS05F | 100 – 230 | 0.04 – 0.12 | ||
|
Titanium alloys Ti-6AI-4V, etc. |
– | First choice | AH130 | 40 – 90 | 0.04 – 0.1 | |
| Superalloys Inconel718, etc. |
– | First choice | AH130 | 45 – 65 | 0.04 – 0.09 | ||
|
Hardened steel | SKD61 / X40CrMoV5-1, etc. |
40 – 50 HRC | First choice | AH120 | 45 – 70 | 0.04 – 0.08 |
| SKD11 / X153CrMoV12, etc. |
50 – 60 HRC | First choice | AH120 | 40 – 65 | 0.04 – 0.06 | ||
Threading
VMT, VTR
| ISO | วัสดุชิ้นงาน | Condition | Tensile strength [N/มม.2] | ค่าความหนา HB |
ความเร็วตัด (ม./นาที) |
Tool dia. (มม.) | ||||
|---|---|---|---|---|---|---|---|---|---|---|
| อัตราป้อน (มม./ฟัน) | ||||||||||
| AH725 | ø10 | ø12 | ø15.4, ø15.7, ø16 | ø21.7 | ||||||
|
Non-alloy steel and cast steel, free cutting steel | < 0.25 %C | Annealed | 420 | 125 | 100 – 250 | 0.08 | 0.09 | 0.12 | 0.15 |
| ≥ 0.25 %C | Annealed | 650 | 190 | 80 – 210 | 0.08 | 0.09 | 0.12 | 0.15 | ||
| < 0.55 %C | Quenched and tempered | 850 | 250 | 65 – 170 | ||||||
| ≥ 0.55 %C | Annealed | 750 | 220 | 110 – 180 | 0.07 | 0.08 | 0.1 | 0.12 | ||
| Quenched and tempered | 1000 | 300 | 95 – 160 | 0.07 | 0.08 | 0.1 | 0.12 | |||
| Low alloy steel and cast steel (less than 5% of alloying elements) |
Annealed | 600 | 200 | 90 – 160 | 0.05 | 0.05 | 0.07 | 0.08 | ||
| Quenched and tempered | 930 | 275 | 65 – 200 | 0.05 | 0.05 | 0.07 | 0.08 | |||
| 1000 | 300 | 70 – 210 | 0.05 | 0.05 | 0.07 | 0.08 | ||||
| 1200 | 350 | 95 – 160 | 0.05 | 0.05 | 0.07 | 0.08 | ||||
| High alloyed steel, cast steel, and tool steel | Annealed | 680 | 200 | 130 – 170 | 0.05 | 0.05 | 0.07 | 0.08 | ||
| Quenched and tempered | 1100 | 325 | 75 – 100 | 0.05 | 0.05 | 0.07 | 0.08 | |||
| Stainless steel and cast steel | Ferritic/martensitic | 680 | 200 | 110 – 170 | 0.05 | 0.05 | 0.07 | 0.08 | ||
| Martensitic | 820 | 240 | 70 – 155 | 0.05 | 0.05 | 0.07 | 0.08 | |||
|
Stainless steel | Annealed | 600 | 180 | 85 – 100 | 0.05 | 0.05 | 0.07 | 0.08 | |
|
Cast iron nodular (GGG) | Ferritic/martensitic | 180 | 120 – 160 | 0.08 | 0.09 | 0.12 | 0.15 | ||
| Pearlitic | 260 | 75 – 160 | 0.08 | 0.09 | 0.12 | 0.15 | ||||
| Grey cast iron (GG) | Ferritic | 160 | 70 – 150 | 0.08 | 0.09 | 0.12 | 0.15 | |||
| Pearlitic | 250 | 110 – 140 | 0.08 | 0.09 | 0.12 | 0.15 | ||||
| Malleable cast iron | Ferritic | 130 | 120 – 160 | 0.08 | 0.09 | 0.12 | 0.15 | |||
| Pearlitic | 230 | 110 – 140 | 0.08 | 0.09 | 0.21 | 0.15 | ||||
|
Aluminium-wrought alloy | Not cureable | 60 | 160 – 300 | 0.08 | 0.09 | 0.12 | 0.15 | ||
| Cured | 100 | |||||||||
| Aluminium-cast, alloyed | ≤12% Si | Not cureable | 75 | 150 – 350 | 0.08 | 0.09 | 0.12 | 0.15 | ||
| Cured | 90 | |||||||||
| >12% Si | High temperature | 130 | 100 – 250 | 0.05 | 0.05 | 0.07 | 0.08 | |||
| Copper alloys | >1% Pb | Free cutting | 110 | |||||||
| Brass | 90 | |||||||||
| Electrolitic copper | 100 | |||||||||
| Non-metallic | Duroplastics, fiber plastics | 100 – 400 | 0.11 | 0.12 | 0.15 | 0.18 | ||||
| Hard rubber | ||||||||||
|
High temp. alloys | Fe based | Annealed | 200 | ||||||
| Cured | 280 | |||||||||
| Ni or Co based | Annealed | 250 | 20 – 80 | 0.03 | 0.03 | 0.04 | 0.04 | |||
| Cured | 350 | |||||||||
| Cast | 320 | |||||||||
| Titanium Ti alloys | RM 400 | |||||||||
| Alpha+beta alloys cured | RM 1050 | 20 – 80 | 0.03 | 0.03 | 0.04 | 0.04 | ||||
|
Hardened steel | Hardened | 55 HRC | 55 – 65 | ||||||
| Hardened | 60 HRC | 45 – 55 | ||||||||
| Chilled cast iron | Cast | 400 | 90 – 105 | |||||||
| Cast iron | Hardened | 55 HRC | 55 – 65 | |||||||
ไปที่ e-catalog ออนไลน์ของเรา หรือดาวน์โหลดรายงานสินค้าเพื่อดูข้อมูลเพิ่มเติมเกี่ยวกับผลิตภัณฑ์นี้:
e-Catalog
Industries |
|
Industries Learn more |
e-Catalog |
|
e-Catalog Learn more |
แหล่งข้อมูล
Tungaloy APP
TUNG Naviตัวช่วยในการเลือกเครื่องมือ
Machine Power Calculator
Turning Insert Selection Guide
Matrixระบบจัดการผลิตภัณฑ์อัจฉริยะ