
Indexable gun drill with exceptional efficiency
DeepTri-Drill, the easy-to-handle, indexable gundrill series, delivers outstanding performance, exceptional efficiency and stability in deep hole drilling
Applications & Features
Applications

Small-diameter drilling
Features
1. Wide range of options for various deep hole applications
2. Ultimate efficiency
• Unique chip breaker and chip splitter on the cutting edge enables impressive chip control at any feed rate, especially at higher feeds
• Thanks to smooth chip evacuation, deep hole making (drilling) is possible even with a standard coolant pressure of 1-2 MPa (145-290 psi)
3. Excellent roundness, straightness, and surface finish
• Special cutting edge geometry and optimized guide pads provide exceptional hole quality.
Inserts & Grades
Inserts
TOHT-NDJ/NDL
- 3 cutting edges inserts with chip splitter
LOGT-NDJ
- 2 cutting edges inserts with chip splitter
ZSGT-NDJ
- Single sided insert with chip splitter
Main Grades
AH9130
- P15 – P35 / M25 – M35 / K10 – K25 / S15 – S30
- High wear resistance
- Designed for drilling various materials
AH725
- P15 – P30 / M15 – M30 / K25 – K30 / S15 – S25
- Good balance between wear and chipping resistance
- Suitable for machining steel and stainless steel under general cutting conditions
FH3125 (For guide pads)
- First recommendation
- Long tool life due to unique substrate and coating
FH3135 (For guide pads)
- High fracture resistance
- First choice when using water-soluble coolant
Drill bodies
Practical examples
Example #1
Heat Exchanger Industry
Part: | Tube Sheet |
Material: | SUS304 / X5CrNi18-9 |
Drill: | MCTR20.00XM32-10 |
Insert: | TOHT090305R-NDL |
Grade: | AH725 |
Cutting conditions: | Vc = 80 (m/min) f = 0.04 (mm/rev) Vf = 53 (mm/min) H = 200 (mm) Coolant: Wet Machine: Horizontal M/C |

Example #2
Die and Mold Industry
Part: | Plastic mold |
Material: | SKD61 / X40CrMoV5-1 (45 HRC) |
Drill: | TRLGCH18.00X1500-36A |
Insert: | TOHT080305R-NDJ |
Grade: | AH725 |
Cutting conditions: | Vc = 62 (m/min) f = 0.04 (mm/rev) Vf = 44 (mm/min) H = 700 (mm) Coolant: Wet Machine: Horizontal M/C |

Example #3
Automotive Industry
Part: | Shaft |
Material: | SCM420H |
Drill: | MCTR12.00XM20-20 |
Insert: | LOGT060204R-NDJ |
Grade: | AH725 |
Cutting conditions: | Vc = 150 (m/min) f = 0.13 (mm/rev) Vf = 517 (mm/min) øDc = 12 (mm) H = 233 (mm) Coolant: Wet Machine: Vertical M/C |

Standard cutting conditions
ISO | Workpiece material | Priority | Chip-breaker | Cutting speed Vc (m/min) |
Feed:f (mm/rev) | ||||
---|---|---|---|---|---|---|---|---|---|
ø10 – ø11.8 | ø12 – ø13.99 | ø14 – ø18 | ø18.01 – ø28 | ø28.01 – ø40 | |||||
![]() |
Low carbon steel (C < 0.3) SS400 / St42-1, SM490 / St52-3, S25C / C25, etc. |
For low feed machines | NDL | 50 – 100 | – | – | 0.03 – 0.1 | 0.03 – 0.1 | – |
First choice | NDJ/G | 80 – 140 | 0.05 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.05 – 0.1 | 0.1 – 0.2 | ||
Carbon steel (C > 0.3) S45C / C45, S55C / C55, etc. |
For low feed machines | NDL | 50 – 100 | – | – | 0.03 – 0.1 | 0.03 – 0.12 | – | |
First choice | NDJ/G | 80 – 140 | 0.05 – 0.14 | 0.05 – 0.16 | 0.05 – 0.16 | 0.05 – 0.2 | 0.1 – 0.2 | ||
Low alloy steel (C < 0.3) SCM415, 18CrMo4, etc. |
For low feed machines | NDL | 50 – 100 | – | – | 0.03 – 0.1 | 0.03 – 0.1 | – | |
First choice | NDJ/G | 80 – 140 | 0.05 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.05 – 0.1 | 0.1 – 0.2 | ||
Alloy steel (C > 0.3) SCM440 / 42CrMo4, SCr420 / 20Cr4, etc. |
For low feed machines | NDL | 50 – 100 | – | – | 0.03 – 0.1 | 0.03 – 0.12 | – | |
First choice | NDJ/G | 80 – 120 | 0.05 – 0.14 | 0.05 – 0.16 | 0.05 – 0.16 | 0.05 – 0.2 | 0.1 – 0.2 | ||
![]() |
Stainless steel (Austenitic) SUS304 / X5CrNi18-9, SUS316 / X5CrNiMo17-12-3, etc. |
For low feed machines | NDL | 50 – 100 | – | – | 0.03 – 0.06 | 0.03 – 0.06 | – |
First choice | NDJ/G | 60 – 100 | 0.05 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.05 – 0.1 | 0.1 – 0.15 | ||
Stainless steel (Martensitic, Ferritic) SUS430 / X6Cr17, SUS416 / X12CrS13, etc. |
For low feed machines | NDL | 50 – 100 | – | – | 0.03 – 0.06 | 0.03 – 0.06 | – | |
First choice | NDJ/G | 60 – 100 | 0.05 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.05 – 0.1 | 0.1 – 0.15 | ||
Stainless steel (Precipitation hard- ening) SUS630 / X5CrNiCuNb16-4, etc. |
For low feed machines | NDL | 50 – 100 | – | – | 0.03 – 0.06 | 0.03 – 0.06 | – | |
First choice | NDJ/G | 60 – 100 | 0.05 – 0.08 | 0.05 – 0.1 | 0.05 – 0.1 | 0.05 – 0.1 | 0.1 – 0.15 | ||
![]() |
Grey cast iron FC250 / GG25 / 250, etc. |
For low feed machines | NDL | 50 – 100 | – | – | 0.03 – 0.15 | 0.05 – 0.18 | – |
First choice | NDJ/G | 80 – 140 | 0.05 – 0.2 | 0.05 – 0.25 | 0.05 – 0.25 | 0.05 – 0.3 | 0.1 – 0.3 | ||
Ductile cast iron FCD700 / 700-2, etc. |
For low feed machines | NDL | 50 – 100 | – | – | 0.03 – 0.15 | 0.05 – 0.18 | – | |
First choice | NDJ/G | 80 – 140 | 0.05 – 0.2 | 0.05 – 0.25 | 0.05 – 0.25 | 0.05 – 0.3 | 0.1 – 0.3 | ||
![]() |
Aluminium alloys | For low feed machines | NDL | 80 – 160 | – | – | 0.03 – 0.15 | 0.03 – 0.15 | – |
First choice | NDJ/G | 100 – 200 | 0.05 – 0.18 | 0.05 – 0.2 | 0.05 – 0.2 | 0.05 – 0.2 | 0.1 – 0.25 | ||
![]() |
Heat-resistant alloys Inconel 718, etc. |
For low feed machines | NDL | 20 – 50 | – | – | 0.03 – 0.06 | 0.03 – 0.08 | – |
First choice | NDJ/G | 20 – 50 | 0.04 – 0.06 | 0.04 – 0.08 | 0.04 – 0.08 | 0.04 – 0.1 | 0.06 – 0.13 | ||
Titanium alloys Ti-6Al-4V, etc. |
For low feed machines | NDL | 30 – 60 | – | – | 0.03 – 0.1 | 0.03 – 0.12 | – | |
First choice | NDJ/G | 30 – 60 | 0.04 – 0.1 | 0.05 – 0.13 | 0.05 – 0.13 | 0.05 – 0.15 | 0.1 – 0.18 | ||
![]() |
Hardened steel ≥ 40HRC |
For low feed machines | NDL | 40 – 100 | – | – | 0.03 – 0.08 | 0.03 – 0.08 | – |
First choice | NDJ/G | 50 – 100 | 0.04 – 0.06 | 0.04 – 0.08 | 0.04 – 0.08 | 0.04 – 0.1 | 0.06 – 0.13 |
For more information about this product, visit our online e-catalog or download the product report:
Metric
Drill body
Guide pad
Imperial
Drill body
BuscarBuscar
Related News
Recursos
Tungaloy APP
TUNG NaviRecomendaciones de herramientas para sus necesidades específicas
Machine Power Calculator
Turning Insert Selection Guide
MatrixSistema de gestión de herramientas